New Poster
•
2 Messages
Voice control not working
I'm trying to help my elderly neighbor and customer service is absolutely no help. Her remote won't respond to voice commands. All other functions work, on/off volume. If we push the mic button it tells us "somethings not right, try again later". We've paired, unpaired, paired again, made two calls to Customer service totalling 1.5 hours with no resolution. Their response is go get new remotes. I took the remote from her bedroom and tested it there and it responded to voice commands. I brought that remote out to the living room and paired it with the tv out there (replacing the remote that wouldn't respond). It did not respond. Took it back in the bedroom and paired it to that tv and it worked again. This leads me to believe that this isn't a remote issue. My neighbor just wants to speak into her remote. She can't seem to get the hang of using the guide or just entering the channel number. This is important to her and I can't seem to get any resolution. Please help!
Official Solution
CCMacey
Gold Problem Solver
•
541 Messages
3 years ago
Good morning, @gailandrews429, and thank you for reaching out through our Community Forums page for assistance with your voice remote not working correctly! There are a few things you can try, but the steps depend on which model of remote you have. You can find the model number on the inside of the battery cover, and would most likely says XR11 or XR15.
XR11 Voice Control Remote Issue
XR15 Voice Control Remote Issue
Rebooting your X1 main box is also a good troubleshooting step as well, as this will ensure your box has all the most recent updates and correct signals.
0
0
Accepted Solution
EtB123
New Poster
•
2 Messages
5 years ago
Thank you for suggestions. I unplugged from the power and restarted. Works fine. Sometimes it's the easiest things. "It ain't got no gas in it." - Carl, Sling Blade
0
CCAndrew
Gold Problem Solver
•
25.9K Messages
5 years ago
0
0
Rustyben
Expert
•
24.6K Messages
5 years ago
adding ...
the remote is 'RF' (radio) paired to the set top box. taking one that is paired to box 'A' to box 'B' still works box 'B' if it is in range. There are commands to issue/press on the remote to reassign a remote to a different set top box. On the original problem. I seldom have the problem you are describing, and until yesterday it had been some months since the last time. last night I had problems on 2 set top boxes giving the same problem 'something's not right' and that 'off sound' from the remote. after trying the button 3-4 times it then worked. It could be that the server that the set top box sends the voice message to for decoding was overloaded or rebooting, etc.
0
0
user_429
New Poster
•
4 Messages
4 years ago
I have the same problem . I have tried restarting, new batteries, no help. I speak clearly but many times I get random stuff so I just give up.
Maybe asking for a new remote would help I don't know. Glad to see it's not just me struggling. I'm sure there is a solution, would love to see it.
1
0
user_212d7b
Visitor
•
1 Message
3 years ago
I just had this very issue, all the buttons on the X15 remote worked fine, except for the voice control. It kept saying "something's not right try again later". I tried resetting, re-pairing the remote, I even tried factory resetting the remote, all I got was the same message. I went and got the remote from the living room and reset it back to factory and paired it to the box in the room where the voice side wasn't working, and all the buttons worked, except for the voice side of the remote. I paired the bedroom remote to the TV in the living room and everything worked fine including the voice side of the remote, so it wasn't a remote issue. In the meantime I had shut down and restarted the box in both the living room and bedroom, went back through the whole process of resetting back to factory settings, and the voice side still gave me the same on screen message. I should mention, when I went into the onscreen settings it showed the voice commands as "on" yet all I would get is the remote beep, and the on screen message "something's not right, try again later".
I did this four times, four separate times I went though this long process of pairing, re-pairing, shutting down, rebooting if it hadn't worked after the fourth time I was going to rip out the box and march it back to the store Xfinity store and get a replacement and go though the whole process for a fifth time, after all I had nothing better that I could've been doing (sarcasm). However, after the fourth attempt the voice side of the X15 remote worked. Still, it shouldn't be that hard, or require that much shutting down and re-booting, re-pairing etc, etc.
If you have this problem, you may just want to unplug everything the power, the HDMI cable, and let it sit for a few minutes, reset the remote to factory settings and re-pair the remote. But be prepared it may take more than one attempt....
0
user_ae82f2
Visitor
•
1 Message
3 years ago
Try going to the home page, press the Flex home button. Then, using the arrow buttons, select the small gear symbol on the upper left corner. You should see the settings menu. Scroll down to and select Remote Settings. Scroll to Voice Control. If it's Off, turn it On. I don't know why there's a "voice control not working" instead of a Voice Control Is Off.
0
0
user_05faf7
Visitor
•
1 Message
3 years ago
When mine does this, I unplug the set top box and restart it. Works for me but annoying. Had no problems for a year. Now several times in the last month.
0
0
user_2b0ad0
Visitor
•
2 Messages
3 years ago
Guess what mine keeps doing?? My bedroom remote is trying to pair with the living room TV! My XR11 remote works fine for everything on the bedroom TV (cable box to change channel, operate TV power and sound bar volume) .... BUT the voice remote function does not work. Every time I try to re-pair it, I have discovered that the 3 digit code comes up on the living room TV screen. So frustrating.... Any idea how to circumvent this? The XR15 remote works fine in the living room, including the voice control function. Just trying to get the bedroom voice remote function to work.
1
0