6863537's profile

Frequent Visitor

 • 

9 Messages

Sun, Jan 5, 2020 1:00 PM

Can't program XR15 with Sharp tv

I have gone thru all the codez and nothing. The TV is about 2-3 yrs old. So are there other codes to try? Any thoughts?

Responses

Accepted Solution

New Poster

 • 

1 Message

2 y ago

Sharp TV's are made in China by HISENSE. I have a Sharp and used the codes for HISENSE. Try these codes: 

12183
10748
11758

Visitor

 • 

1 Message

@DDAUGHERTY1 

The Hisense code 12183 worked on my Sharp tv.  Wish I’d found your post 3 hours ago.

Thank you so much!!!  

CCAndrew

Gold Problem Solver

 • 

25.9K Messages

2 y ago

Have you tried to manually find a code?

Frequent Visitor

 • 

9 Messages

2 y ago

I have been trying to finb codes elsewhere but not yet found any. Any suggestions to where?

Frequent Visitor

 • 

9 Messages

2 y ago

will the XR11 remote work with this new X1 dvr? If so and i cant get this new remote to work, will go that route.

thx

CCAndrew

Gold Problem Solver

 • 

25.9K Messages

2 y ago

For voice commands did you input the given 3 digit code?

To find codes not listed, press A and D, 991 and ch up until the tv turns off

You can also pick an XR11 remote anytime at your local service center

Frequent Visitor

 • 

9 Messages

2 y ago

Yes, I have tried all the XR15 codes. i think i might try the other remotes like the XR11 remote codes to see. I have just drilled down to the Sharp tv so will give them a shot as well.

I also dont have Voice Command working so this XR15 is a bust for me so far.

Frequent Visitor

 • 

9 Messages

2 y ago

how many times? I went about 25 times and no change.

 

Frequent Visitor

 • 

9 Messages

2 y ago

Thanks.

I have tried my XR11 remote with the new X1 dvr and no go. So 2 different remotes and no sync. So could it be the new DVR?

I originally had problems getting this bugger set up even tho it should have been just a plug and play but no go.

Rustyben

Expert

 • 

24.1K Messages

2 y ago


@6863537 wrote:

Thanks.

I have tried my XR11 remote with the new X1 dvr and no go. So 2 different remotes and no sync. So could it be the new DVR?

I originally had problems getting this bugger set up even tho it should have been just a plug and play but no go.


does your sharp TV remote control the TV via IR (dark window on the end of the remote that points toward the TV-test by covering end of remote with palm of hand and press volume or power button)? or by RF (non IR - similar to how the X1 remote talks to the paired X1 set top boxes)?

Frequent Visitor

 • 

9 Messages

2 y ago

well thanks. I thought since this was a fairly new tv, 2-3 yrs old, there must be something i am doing wrong.

Now have to deal with 2 remotes to watch tv. not optimum.

 

CCAndrew

Gold Problem Solver

 • 

25.9K Messages

2 y ago

If you went that much, and you did it properly, there’s no compatible code. Odd for a Sharp but it happens. The DVR has nothing to do with setting up your codes.

New Poster

 • 

1 Message

2 y ago

This worked!!!  Thank you so much, i've been looking everywhere for that code.


@DDAUGHERTY1 wrote:

Sharp TV's are made in China by HISENSE. I have a Sharp and used the codes for HISENSE. Try these codes: 

12183
10748
11758


 

Frequent Visitor

 • 

9 Messages

2 y ago

That worked. Great and thanks.

Code 12183 worked.

dwebb

New Poster

 • 

1 Message

2 y ago

Thank you! this helped me as well I have a 43k325uw Sharp and 11758 worked for me

New Poster

 • 

1 Message

2 y ago

The ONLY code that worked for my sharp tv after going through all codes is 11564

New to the Community?

Start Here