Community Forum
turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
About desmo907
since
09-23-2013
desmo907
Regular Contributor
86
Posts
9
Kudos
1
Solution
10-24-2018
08:08 AM
This morning my phone went off about 20 times... Xfinity sent me a code (via SMS) that many times yet I was sleeping (and nobody in house was trying to access my account).
I wonder if someone was hacking me....(I was able to access my account later and did receive that code too)
Regardles, Xfinity should have logic in place NOT to send the verification code so many times in a short period of time.....maybe wat 10 minutes...
... View more
07-04-2018
10:46 PM
I have the Coredy 300Mbps WiFi Range Extender and notice that when connected to it (with a cell or tablet) the device does not show up in the xFi app.
Is this an issue with xFi or the extender, or just the way the technology works?
Kids devices are connected to it but do not show up so I cannot manage them...
Thoughts?
... View more
03-11-2018
08:33 AM
Then create a more user-friendly and useful error message so we do not have to bother you here.
... View more
03-05-2018
06:31 AM
In Thailand now in hotel wifi trying to use app to stream live CNN or other shows and get error.
106000 error 5
I even turned off `best playback' option.
Recorded shows....same error.
Both devices newer Samsung...Tab A and Galaxy S8 phone with latest Android.
Nice job comcast.
... View more
01-17-2017
01:54 PM
I am able to "block" a device (I recognize the MAc address) on my personal WiFi network using the Admin interface (my version of parental controls).
However the device can easily get on the default xfinitywifi network.
How do I block the device from getting on that xfinitywifi network as I do not see a feature within the Admin tool.
Thx
... View more
10-05-2013
06:28 PM
1 Kudo
Not sure how it happened but the remote now turns on my Onkyo receiver and adjusts the volume. However it will not turn it off. I have to use the Onkyo remote (and it has a Standby feature not OFF). The remote also turns on/off my Samsung Tv as programmed by installer.
... View more
09-25-2013
02:36 PM
Thanks for the help but mine will not work. After the first code the All button flashes green 2x but the TV (or later the All) button does nothing. After the 2ndcode the All button flashes red then green and the TV (or later the All) button does nothing.
... View more
09-25-2013
06:36 AM
My remote says Version U2. I tried both the codes and they do not work. The All Power light flashes green 2x after I enter 30135 but the TV button does not turn off the Onkyo. If I try the 2nd code 30842, after entering the last digit the All Power light flashes red. This remote has been programmed to control the Samsung TV fine but i really want it to turn on/off(and control the volume) of the Onkyo (not volume of the TV which is left down). My ATT UVerse remote did this perfectly.
... View more
09-24-2013
11:14 AM
I used the Comcast tool to find the codes. They didn't work. And they reference a TV instead of "audio" ("if the TV turns off"). ---- These are the codes for your Onkyo Audio . Follow the instructions below to program your remote. Most likely code : 30135, Others to try : 30842 To program your Comcast remote : Turn on your TV and set-top box or HD DTA. Press and hold the Setup button on your XR2 Remote for 3 seconds until the All Power button changes from red to green. Enter the first code you see above using the numeric buttons on the remote. The All Power button should flash green twice when the code is entered. If the green light emits one long blink, repeat steps 3 and 4, entering the same code. Press the TV Power button on the remote. If the TV turns off, you have successfully programmed your XR2 Remote to control your TV. Turn the TV back on and press the VOL +/- and Mute buttons to confirm they control the volume of your TV. If the TV does not turn off, repeat the steps above using the next manufacturer's code listed above. You may need to try several codes to find one that works for your TV.
... View more
09-24-2013
06:55 AM
I tried to program the XR2 remote to turn on/off (and hopefully adjust volume) my Onkyo HT RC 270 receiver but it does not work. I did a search on the Support site and I found reference (and 2 codes) for Onkyo. However the instructions seems to be related generically as they refer to a "TV: even though I searched "audio". I had uVerse before and their remotes controlled all my devices..... does the XR2 not?
... View more
