Use this tool to find the codes of your devices and to get specific instructions on programming the codes into your Comcast remote.
I have a new VizioVA19LHDTV (19" 720p) and Comcast has provided me a new Cisco-made STB with HDTV and HDMI output (no DVR) designated as RNG-150. It reports the infamous messages, "Copy Protection - The DVI/HDMI output is blocked - Press Exit to Cancel" and then (after pressing exit) "DVI Alert - Your HDTV does not support HDCP. Please use the YPrPb component connection to watch TV." I duplicated the problem with a different HDTV (of course HDCP compliant) which works perfectly when connected to the
This is bogus. Needless to say the HDTV is HDMI compatible. When I connect the Vizio TV to the 8300 HD (DVR box) via the same HDMI cable, there are no issues (in any case I have swapped out both cable and box with no change in the problem status). Likewise, when I connect the TV that is normally on the 8300 HD (a Westinghouse 42") with this RNG-150, I have the same problem.
There may be some kind of internal user setting menu for the RNG-150 that is required to enable HDMI. But no manual for the RNG-150 is provided with the box and the local Comcast dispensary (Woodcrest in Cherry Hill, NJ for me) does not have the manual. It is on the web, kind of: On this page, http://www.comcast.com/corporate/customers/custome
A tech was here and had no clue how to configure the RNG-150 to enable HDMI (if such enablement is required.) He noted that on the STB on-screen menu for the 8300HD under the category Audioigital Output category there are three selections: Dolby, HDMI, and other. But the same menu for the RNG-150 has only Dolby and other. He had not encountered this issue before but said that there was little field experience with this box. His only suggestion was to downgrade the box to the SA 4350 (I think) which evidently is still around.
The CSR's on the phone have nothing to offer except to call a tech, which I did. A very nice lady at the Woodcrest facility told me that they have had lots of problems with these recently-introduced STB's.
By turning on and off the TV and STB, switching cables, etc., I can get the STB and the HDTV to tlak. to each other. But then when I turn off either or both for period of time and turn back on, I get one or the other of the above messages, or a "No signal" from my TV, and I am back where I started.
I can replace the HDMI with composite and have no problems. But I am **bleep** and compulsive and I want this to work with HDMI like it's supposed to. I don't want to use the composite connection and I shouldn't have to. And the problem I described occurs when the only input to the TV is the HDMI cable from the STB. Yes, I know how HDCP is supposed to work and no, nothing else is plugged in at the same time.
Can anybody provide any help with this issue? I cannot be the only person who has experienced this problem since my setup is totally vanilla and the equipment is all new.
07-11-2009 04:37 PM
07-11-2009 05:28 PM
07-11-2009 05:53 PM
10-12-2009 10:43 PM
10-13-2009 08:26 PM
File is corrupt.
10-13-2009 10:05 PM
02-12-2010 08:54 AM
Was this ever resolved? I have a Vizio 42" and a new Cisco RNG 150 that Comast just gave me. After a week's worth of grief, I figured out last night that the problem is the HDMI port on the TV...every port. Works ok with regular composite cables, but I want less cables and better connection with HDMI.
My issue is that when I hit the ALL On button on the remote, the box goes through it's re-boot sequence and takes about 10 minutes for everything to come up. Any help would be appreciated.
04-14-2010 03:55 PM
04-14-2010 04:01 PM
They gave me an old HDTV Box, with HDMI Connection. I connected it all and it worked!
04-14-2010 04:13 PM
I have this issue with the Scientific Atlanta 4250HDC, but it appears to be sporadic and I cannot replicate it on command. While watching live TV a box pops up that says "Copy Protection, DVI/HDMI output blocked...". This blocks the video output but the box still sends the digital audio signal. Reseting the box (unplugging the power not just powering off) seems to resolve the issue for a couple weeks then it pops up again. When I press cancel the screen goes black and I can still access the guide but not tune to any channel and see video, but after several minutes video reappears. At no point does audio stop, however. Calling support they had no solution other than to try to swap out the box.
11-29-2010 11:44 PM
Try and swap the box for something newer like a RNG150.
You are running the HDMI direct without a HDMI switcher or AV receiver, right?
Worst case, you might need to see if there is newer firmware for your TV you can download and install from the TV Mfr.
11-29-2010 11:48 PM
Hi Tedlevy, i dont know if you have found the solution to this problem yet, but i have a question about the out put settings in the RNG...
i've worked directly with RNG-110, i havent seen RNG-150 yet in my market, but i know the RNG-110 model has an out put setting where if you are using HDMI, you will need to adjust, depending on they type of TV. does your box have a user settings menu?
11-30-2010 12:23 AM
04-05-2011 01:16 PM
Alerts are an easy, quick way to manage your account and get information - like payment confirmations and your current balance.
©2011 Comcast | Investor Relations | Press Room | Corporate Blog | Privacy Statement | Visitor Agreement | Xfinity.com Feedback | Site Map