New to the Community? Start here.
Should I turn RNG150N cable box OFF and use TV remote to change brightness etc. Reason being box is now on HDMI-1 but TV is on
INPUT 2. (non HDMI setting) I tried to use TV remote while RNG150N was ON HDMI 2 and resulted in a nightmare --- lost HDMI connection. I restored box setting by switching HDMI-2 to HDMI-1. But, fear trying TV remote again while box is on. Although TV is obviously HDMI capable its inputs only show 1,2,3,4, 5 but no HDMI.
If I turn on TV remote without box on it will open screen and allow me to enter TV settings menu and make changes I want. But, when I turn TV remote off and turn box back on (HDMI) TV picture settings are lost. Sorry to post this as I did once before but was told to contact manufacturer(Hitachi) who could not adress issue. Is a Comcast setting since day box was installed (replaced defective box). I'll, no doubt, end up hooking box up without HDMI.
Thank you anyway,
Check the side of television where the port connections are located. There should be a number by each type of port matching the the number you see when changing the source.
Only one of your ports on the tv may be a HDMI port. The other might be a HDMI to DVI port. That one would not work for you in this case.
Once you find the correct port for the HDMI cable, and change the source on the tv to that number, the cable-box should work after resetting it..
I would unplug the cable-box for at least one minute, and plug it back in for at least 5 minutes to set and reload the cable-box. Then turn it back on.
Thank you for your help. But, see attached buttons on side of TV are same as if using remote. No HDMI input just inputs 1-5. TV obviously is HDMI capable -- also see on attached.
If you have a place to plug a HDMI cable into your tv there should be a number there showing the source to choose when using your remote.
Secondly: Why do you turn off the TV when turning on the cable-box?
I don't turn off the TV when turning on the cable box. The TV screen comes on when I turn box on. Box is connected on HDMI-1 from TV to box. But, I can't use TV remote to adjust brightness etc. (which is on TV's INPUT 1). If I do ,changes will not hold and I lose HDMI connection when I turn TV off with with box remote--thus no picture. HDMI-2 goes to an Oppo HDMI switch (attached).
Sorry for confusion.
Do you have another tv to check the cable-box?
Can you get get the tv to work on OTA channels with the antenna?
The problem is with the television.
The other TV is a CRT SD TV with a SD cable box. Obviously, would not connect to RNG150N.
Am in rural area with no local TV stations so antenna useless.
The television puts out a remarkable picture so if TV is problem I'm not going to junk it and buy another TV (non plasma). Present problem did not start until Comcast replaced defective RNG 110 with current box. So I'll
thanks for your help.
I hope I find answer in RNG150N manual which I could not find on Comcast/Xfinity 's cable boxes manuals list because they only have Cisco and Pace 150 boxes manuals ( totally different). So I had to download correct manual from:
pdf too large to attach to this posting.
I don't want to junk my HD TV because I can't adjust its settings when only cable box is HDMI-1 connected but TV is on input 1,2,3, 4 or 5 (non HDMI inputs). And, fact it worked before Comcast installed box (leaving me to do away with stretched mode installer claimed could not be done). Moreover, if I attempt to access input 1, 2 or 5 on TV to run any of my DVD players when I close I'll lose cable box HDMI setting and picture which happened earlier this week and was a nightmare for me and Comcast CSR to reset.
Keeping my fingers crossed to salvage my plasma TV (attached).
That think is officially old! 2006?
So, it has 2 HDMI inputs. Is that way back when you just pushed the HDMI button on the remote and it would toggle between HDMI 1 & 2? I always disliked that as it made it difficult to 'know' what input it was on when trying to program a custom remote.
When you're adjusting "Brightness" and "Contrast" and such, the TV itself doesn't 'care' what device is plugged in to it. If, while viewing the cable box, you bring up the menu for picture adjustment on the TV and make adjustments, then, without turning anything on or off you switch the HDMI Cable from the cable box to a BluRay Player (or any other HDMI device), the picture won't suddenly 'reset' to a different setting.
What exactly are you saying is happening?
RE: Is that way back when you just pushed the HDMI button on the remote and it would toggle between HDMI 1 & 2?
No HDMI buttons on TV Remote to push. So can only toglle inputs 1,2,3,4 or 5 (hooked to DVD players) I have HDMI-1 plugged into RNG150N. HDMI-2 into OPPO HM-31 (see below) which is connected to BluRay plater and another DVD player (Sony which is lousy only plays 720p or if set to 1080 shrinks picture).
Thanks for your help but situation is hopeless. Had no problem until Comcast installed RNG150N. Yes TV is 2006 model and has been superb but since RNG 150N installed no way to adjust video and audio settings with TV remote due to inputs not HDMI.
RE: That think is officially old! 2006? Yes, but I won't junk it. I may have lucked out getting a TV that has worked for eleven years as my Motorola SD CRT TV has and still is. (also bought in 2006).
Thanks again most appreciated,
Old posting but see D. But, I still won't junk tv (Plasma) and buy an LED TV.
Do you happen to have a DVD player attached with other cables to your television at the present time?
Page 15 in your manual warns that the HDMI port's signal to television will be blocked if a DVD player is attached to protect copyright infringment.
That means you will need to remove the DVD player to get the Cable-box working. Use HDMI 1 for the cable-box.
Yes and have from day one. Inputs 1, 2, 3, 4 and 5 (all non HDMI inputs of course) and never had a problem until RNG150N installed. Also, with TV and box off to avoid another nightmare I turned on BluRay player connected with HDMI-2 to OPPO HM-31 switch and it recognized BluRay player and switched to it. But I did not turn on TV because if I did I would end up with no signal again.
I'll cautiously continue to experiment. Meanwhile TV picture is beautiful ---just turned on TCM.
So the Blu-Ray player was still connected to the tv, along with the cable-box?
Your old tv software is designed to block the signal if any player is connected while watching cable. The new cable-box considers all programming needing copyright protection.
I think you might have to also remove the Blu-Ray player to see if the cable-box works then. The older cable-boxes did not have the copyright protection required at present time. The problem might also come from the switch from MPEG2 to MPEG4 this year due to copyright protection and other modernizing issues.
BluRay Player was connected with HDMI-2 to OPPO HM31. Although it switched to BRP I did not turn on TV or cable box.
RE: I think you might have to also remove the Blu-Ray player to see if the cable-box works then. Cable box works. That is not the problem. Problem is TV remote can't be used to change video and audio settings. Since BRP is connected to HDMI switcher would do nothing to turn off BRP. What is weird is while TV is on using box, of course, if I press Aspect on TV remote provides size choices --standard, zoom and expanded. I of course set it back to standard. But I dare not try to use TV remote MENU for other settings or I'll end up with no picture and NO SIGNAL on screen. As occurred earlier this week and was a nightmare to correct working with Comcast CSR to restore. But at that time Box was on HDMI-2 and OPPO HM31 on HDMI-1. Switched HDMI-2 to HDMI-1 socket on back of TV and picture through box restored.
Thank you for your suggestions but I'd better stop experimenting for awhile. Want to keep my sanity.
Update. I opened a DVD player using its INPUT 2 (NOT HDMI) on TV remote. DVD played perfectly. Cable box RNG150N was off when I did this. However, after I finished testing DVD player and turned off I then tried to use RNG150N remote to access TV picture assuming would work with HDMI-1. It failed showing No Signal and TV's INPUT-2 in upper corner. I unplugged HDMI-1 and replugged in --also unplugged TV and cable box (is now repopulating) Tried again with HDMI-1 but still showed no signal and TV's NPUT 2. So I switched HDMI-1 to HDMI-2 socket and TV came on showing HDMI-2. Tried again to switch to HDMI-1 but no luck. I suppose it does not matter if on HDMI-2 as it was earlier in the week when switching to HDMI-1 resolved. Crazy!
So if I want to watch a DVD I won't (on this TV) due to above inexplicable hassle. I also tried BluRay player but it would not function (is on Oppo HM-31 switch
No replies needed, I'm just going to use HD TV for viewing and nothing more (no DVDs)
Need to switch HDMI-2 back to HDMI-1 This morning after entering TV remote INPUT-2 to test DVD with Comcast RNG150n box OFF upon finishing and attempting to access picture with RNG150n remote showed TV"s INPUT-2 on screen but with NO SIGNAL. So I switched HDMI-1 cable with HDMI-2 in back of TV HDMI sockets.. This restored picture and now shows HDMI-2. Can it be switched back to HDMI-1? If so, how? Or does it make any difference?
I already unplugged TV, and box thinking this would restore HDMI-1 upon restarting both but it did not.
From below: D. After connecting either player to either HDMI input 1 or HDMI input 2, the Hitachi "INFO" screen always displays: Input: 1 or Input: 2 (as it would with a composite video or NO video input); the "INFO" screen never gives any "HDMI" input indication.
But, I still can't figure out how to get HDMI-1 back after having to change to HDMI-2 this morning after playing DVD on TV's INPUT 2 . If I did not source HDMI-2 I'd have no picture.
My last theory but not thinking a wise move would be to go back using TV remote INPUT 2 and play DVD again. And, then when RNG 150n won't work on HDMI-2 swich to HDMI-1 and hope it restores to -------- see attached!
but did before
As for the Panasonic DMP-BD35 BluRay player ----------- that's a lost cause. Just won't work (but did before RGN150n installed.
Topic: Should I turn RNG150N cable box off and use TV remote to change brightness etc
Date: 11-15-2017 04:49 PM
Did it solve your problem? NO!
Click here to view the replies and mark one as an Accepted Solution.
Our hearts go out to those impacted by Storm Riley this past Friday and those who may be impacted this week by Storm Quinn in the Northeast Division.
To help residents and emergency personnel stay connected during this time, Comcast is opening up Xfinity WiFi outdoor and SMB hotspots in these communities to anyone who needs them, including non-Xfinity Internet subscribers.
This will be starting at 4:00 PM ET on Monday, March 5, 2018, through Friday, March 16, 2018.
For more about these open Xfinity Hotspots see here.
Alerts are an easy, quick way to manage your account and get information - like payment confirmations and your current balance.